How to Clean Your Gun With WD40

Before you start cleaning your gun with WD40, make sure it’s unloaded, pointed in a safe direction, and the action is open. Wear protective gear and lay out a soft, flat surface to work on. Spray a light, even coating of WD40 onto the entire firearm to loosen grime or debris. Let it penetrate for a few minutes to break down stubborn buildup. Then, wipe down the gun surfaces with a microfiber cloth or gun cleaning brush to remove dirt, grime, and fingerprints. Remove excess WD40 residue and inspect your gun for rust, blockages, and wear. Now that you’ve started cleaning your gun, learn how to finish the job and keep your firearm in top condition.

Preparing Your Gun for Cleaning

Before you begin cleaning your gun, always verify it’s completely unloaded and pointed in a safe direction, with the action open and any magazine removed.

This is a critical safety protocol to guarantee you and those around you’re protected from accidental discharge. Gun maintenance is a serious responsibility, and you must take it seriously.

Next, lay out a clean, flat surface to work on, such as a table or countertop.

Cover it with a soft cloth or gun mat to prevent scratching your firearm. Remove any accessories, such as scopes or flashlights, to prevent damage during the cleaning process.

Take a moment to visually inspect your gun, looking for any signs of wear or damage that may require special attention.

Applying WD40 to the Gun

As you prepare to clean your gun, grab a can of WD40 and give the entire firearm a light, even coating to loosen any grime or debris that may be stuck to the surface. Make sure to hold the can upright and spray from a distance of 8-10 inches to avoid over-saturating the gun. This will help break down any tough residue and make the cleaning process much easier.

Remember, gun safety is vital during this process, so verify you’re pointing the gun in a safe direction and keeping your finger off the trigger.

If you’re looking for WD40 alternatives, you can also consider using silicone-based lubricants or gun-specific cleaners. However, WD40 is a popular choice due to its effectiveness and affordability.

Important Reminders:

  1. Always wear protective gloves and eyewear when cleaning your gun.
  2. Make certain the gun is unloaded and the action is open before applying WD40.
  3. Avoid spraying WD40 directly into the barrel or any small crevices, as this can cause damage.

Letting WD40 Penetrate Deposits

You’re now letting the WD40 penetrate the deposits, allowing it to break down the grime and loosen tough deposits that have built up on your gun.

As you wait, the WD40 is working to dissolve the stubborn residue, making it easier for you to wipe away later.

Breaking Down Grime

Letting WD40 penetrate deposits allows the solvent to break down even the toughest grime, making subsequent cleaning steps much more effective. As you let the WD40 sit, its solvent properties go to work, loosening and breaking down the grime buildup that’s accumulated on your gun. This is especially important because grime buildup can be incredibly stubborn, requiring a powerful solvent to dissolve and remove it.

  1. Breaks down tough grime: WD40’s solvent properties allow it to dissolve even the most stubborn grime buildup.
  2. Prepares for cleaning: By breaking down grime, WD40 makes it easier to wipe away dirt and debris in subsequent cleaning steps.
  3. Guarantees a thorough clean: Letting WD40 penetrate deposits guarantees that you’re removing all the dirt and grime, not just the surface-level debris.

Loosening Tough Deposits

With WD40 applied, give it time to penetrate the deposits, allowing the solvent to seep into every crevice and corner of your gun’s surface.

This is where the solvent properties of WD40 come into play, breaking down the tough deposits that have built up on your gun. As you wait, the WD40 will start to dissolve the grime, making it easier to remove.

Take this opportunity to analyze the deposits on your gun.

Are they particularly stubborn? Are they concentrated in specific areas? This deposit analysis will help you identify areas that need extra attention during the cleaning process.

As the WD40 penetrates deeper, you’ll start to notice the deposits loosening, making them easier to remove. Be patient, as this process can take some time. But with the solvent properties of WD40 on your side, you’ll be well on your way to a clean and well-maintained gun.

Wiping Down the Gun Surfaces

Now that you’ve let the WD40 penetrate the deposits, it’s time to wipe down the gun surfaces.

You’ll want to prepare the metal, remove any fingerprints, and achieve a smooth exterior shine.

Gun Metal Preparation

You’ll begin gun metal preparation by wiping down the gun surfaces, removing any dirt, grime, or debris that may have accumulated during use. This step is essential in ensuring your gun is clean and free from any contaminants that may affect its performance.

Rust prevention is a critical aspect of gun maintenance. A clean surface is essential for rust prevention. Any dirt or grime left on the metal can lead to rust and corrosion, which can compromise the integrity of your gun.

Metal conditioning is another important benefit of wiping down the gun surfaces. This helps in metal conditioning, allowing the WD40 to penetrate deeper and provide maximum protection.

Removing Fingerprints Easily

After wiping away dirt and grime, turn your attention to removing fingerprints, which can leave behind oils that interfere with the WD40’s ability to protect your gun’s metal surfaces. Fingerprints can be a challenge to remove, but it’s vital to eliminate them to create a clean slate for the WD40 to work its magic.

Here’s a comparison of fingerprint removal methods:

MethodEffectiveness
Microfiber cloth8/10 (gentle, yet effective)
Gun cleaning brush6/10 (can scratch surfaces)
Fingerprint forensic wipes9/10 (designed for fingerprint removal)
Paper towels4/10 (can leave behind lint)

When removing fingerprints, remember that oil resistance is key. You want to remove the oils from your skin without leaving behind new substances that could interfere with the WD40. By using a microfiber cloth or fingerprint forensic wipes, you’ll be able to effectively remove fingerprints and create an ideal surface for the WD40 to bond with, thereby providing a reliable foundation for its protective properties to take hold.

Exterior Surface Shine

How can you achieve a showroom shine on your gun’s exterior surfaces? By following a few simple steps, you can give your gun a cosmetic appeal that turns heads. After removing fingerprints and grime, it’s time to add a protective coating to your gun’s exterior.

There are three ways to achieve a dazzling exterior surface shine:

  1. Microfiber cloth and WD40: Gently wipe down your gun’s surfaces with a microfiber cloth and a small amount of WD40. This will remove any remaining impurities and leave a subtle sheen.
  2. Gun wax or polish: Apply a gun wax or polish to a soft cloth and buff your gun’s surfaces. This will create a deeper, more intense shine.
  3. Silicone-based spray: For a quick and easy solution, use a silicone-based spray specifically designed for guns. These sprays provide a protective coating and can be wiped off with a microfiber cloth for a showroom shine.

Removing Excess WD40 Residue

When wiping down your gun, be careful not to leave excess WD40 residue, which can attract dirt and dust, and compromise the weapon’s performance over time.

To prevent this, use a clean, lint-free cloth to wipe away any excess WD40. You can also use a WD40 alternative, such as Break-Free CLP or Hoppe’s No. 9, which are designed to leave less residue behind.

For residue prevention, apply a small amount of WD40 to your cloth, rather than spraying it directly onto the gun. This will help you avoid over-saturating the surface and reduce the risk of residue buildup.

Additionally, avoid using WD40 on hot or dirty guns, as this can increase the likelihood of residue accumulating. By taking these precautions, you can guarantee a clean and well-maintained weapon that performs at its best.

Inspecting and Drying the Gun

You should now inspect the gun’s exterior and interior for any remaining dirt, grime, or moisture, paying close attention to crevices and areas where buildup tends to accumulate. This step is vital to guarantee your gun is thoroughly cleaned and safe to handle.

As you inspect, make sure to check for the following:

Check for rust: Pay attention to areas prone to rust, such as the chamber and barrel, and remove any rust spots to prevent further damage.

Verify gun safeties: Confirm that all gun safeties are functioning correctly, including triggers, hammers, and other mechanisms.

Dry all surfaces: Use a soft cloth to wipe down the entire gun, paying extra attention to crevices and areas where moisture tends to collect.

Frequently Asked Questions

Can I Use WD40 on All Types of Guns and Ammunition?

You should exercise caution when using WD40 on all types of guns and ammunition, as some guns have sensitive materials and certain ammo can be damaged, so you must check gun compatibility and ammunition sensitivity first.

How Often Should I Clean My Gun With WD40 for Maintenance?

You should establish a regular cleaning schedule for gun maintenance, with frequency guidelines suggesting you clean your gun every 3-6 months, or after every 200-300 rounds, to maintain peak performance and safety.

Will WD40 Damage the Gun’s Finish or Harm the Bluing?

When using WD40, you should prioritize finish protection and bluing preservation. Be cautious, as WD40 can strip the bluing and damage the finish; instead, opt for a gentle, gun-specific cleaner to facilitate a safe cleaning process.

Can I Use WD40 to Clean Gun Accessories Like Scopes and Holsters?

When cleaning gun accessories, you can use WD40 on scopes for scope maintenance, but avoid it on holsters, opting instead for a gentle conditioner to maintain holster conditioning and prevent damage.

Is It Safe to Use WD40 on Guns With Stainless Steel Components?

When using WD40 on guns with stainless steel components, you risk stainless reactivity and metal corrosion, so it’s not recommended; instead, opt for a gentle, stainless-steel-friendly cleaner to protect your gun’s longevity and performance.

Shopping Basket
Scroll to Top

By continuing to use the site, you agree to the use of cookies. more information

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.

Close